Approved Document P
The building regulations establish standards that must be achieved in the construction of buildings.
Part P of Schedule 1 to the Building Regulations requires that, ‘Reasonable provision shall be made in the design and installation of electrical installations in order to protect persons operating, maintaining or altering the installations from fire or injury.’
This applies to electrical installations intended to operate at low or extra-low voltage, that are:
- In or attached to a dwelling.
- In the common parts of a building serving one or more dwellings, but excluding lifts.
- In a building that receives its electricity from a source located within or shared with a dwelling.
- In a garden or in or on land associated with a building where the electricity is from a source located within or shared with a dwelling.
In order to meet this requirement, low voltage and extra-low voltage electrical installations in dwellings must be designed and installed to give appropriate protection against mechanical and thermal damage and not to present electric shock and fire hazards to individuals.
A series of Approved Documents set out what typically would be acceptable for compliance with the relevant requirements of Building Regulations. There is no legal obligation to follow the guidance in the Approved Documents.
Approved Document P - Electrical safety – Dwellings, describes methods for ensuring compliance with the electrical safety requirements for homes in relation to Part P of the Building Regulations. The most recent edition was published in January 2013 and came into effect in April 2013. It replaced Approved Document P (2006) which incorporated 2010 amendments. The main changes brought in by the 2013 edition included:
- A reduction in the range of the electrical installation work that is notifiable to a building control body.
- Installers not a registered a competent person are permitted to use a 'registered third-party certifier' to certify work, as an alternative to a using building control body.
- The technical guidance refers to BS7671:2008 Requirements for Electrical Installations, incorporating Amendment No 1:2011.
The content of the Approved Document includes:
- Section 1: Design and installation - There is a general requirement that electrical installations should be designed and installed in accordance with BS7671:2008.
- Section 2: Application of Part P – This section covers the types of buildings and installations that are covered by the Scope of Part P and the types of work that are notifiable and must be certified as complying with Building Regulations.
- Section 3: Certification, inspection and testing – Certification of notifiable installations is required, along with inspecting and testing in accordance with BS7671.
- Appendix A: Key terms.
- Appendix B: Standards referred to.
Parts A, B, C, E, F, L and M of the Building Regulations also contain provisions relating to electrical installations.
[edit] Related articles on Designing Buildings
- 2021 PRS electrical safety standards.
- Approved documents.
- Approved inspector.
- BS 7671.
- Building control body.
- Building notice.
- Building regulations.
- Competent person schemes.
- Electrical contractor.
- Electrical engineer.
- Electrical safety.
- Electrician.
- Glossary of electrical terms.
- Low voltage.
- Mechanical and electrical.
Featured articles and news
Download your free guide.
Four new types of prior approval for solar developments
Online Planning Portal application types from 5 September.
Election fails to spark construction industry revival
Contract awards and planning; post election.
Making diversity and inclusion easy for SMEs
The CIOB tool for companies with limited resources.
Sustainable Futures: Redefining Retrofit for Net Zero Living
BSRIA Briefing 2024, initial speakers announced.
Looking back at the UK's first Passivhaus leisure centre
Reflections on St Sidwell’s Point with CIAT.
A-Level results and electrical apprenticeships
Electrical Skills Index highlights areas with skills shortages.
One of the world's more unusual drive-throughs.
A quick introduction.
Hadrian's Wall Path and the national trails
The trails are heritage assets in their own right.
Articles on timely advice and hydraulic lime.
Building Designers Association of Australia
CIAT and BDAA sign Memorandum of Understanding.
Built Environment Inclusive partners issue statement committed to inclusion.
Building regulation requirements can have unintended consequences.
CIOB announces 2024/25 vice president
Sustainability champion Professor Saul Humphrey.
Accelerating towards a net-zero built environment.